S8Q-PA Sterilight ultraviolet UV water purifier Save 52% Off

S8Q-PA Sterilight ultraviolet UV water purifier
  • Electronic -Inch ICE-Inch ballasts featuring open loop current control (patent pending), ballast features quick-lock molded lamp connector, audible alarm and power-on indicator
  • 99.99-Percent destruction of bacteria, virus, and protozoan cysts (Giardia lamblia and cryptosporidium) at rated flow
  • Easy servicing - no need to disconnect water flow to change UV lamp
  • Seven year warranty on reactor chamber for unparalleled protection
  • CSA and CE compliant

I live upstate and depend on well water. After shocking our system twice, we still had bacteria in the water. I finally broke down and installed this unit and it worked! It passed the water lab tests and have been very happy with this unit. No more bacteria! Keep in mind you need to replace the UV bulb every year which can run about $70. Also a good idea to install a water filter between the well and the UV system to keep the bulb clean and free of debris.

Buy S8Q-PA Sterilight ultraviolet UV water purifier Now

We can finally drink our well water! Our drilled private well had a problem with non-coliform bacteria. The test result was in the highest range that the test could measure. Over the past few years we tried several remediation attempts with no luck. A few weeks ago we had this filter installed by a plumber along with a 1 micron sediment filter. It looks like it was a fairly simple installation. Just retested and the result for non-coliform and total coliform bacteria both came back with NONE PRESENT. I expected it to be reduced, but I was surprised it was measured at 0. Very happy with this product.

Read Best Reviews of S8Q-PA Sterilight ultraviolet UV water purifier Here

I ordered the water purifier as my well water had some intermittent bacteria problems and I was tired of shocking my well. The product is easy to install and does a great job. I would highly recommend the product and especially the vendor. I ordered a replacement bulb at the same time I ordered the purifier. The extra bulb had one of the pins damaged during shipping. I emailed the vendor Abundant Flow Water Systems and they had a replacement lamp shipped immediately. If you want a good product from a reliable vendor Abundant Flow Water Systems.

Want S8Q-PA Sterilight ultraviolet UV water purifier Discount?

Product works as described. Quality is the best and the installation instructiins were easy to follow. It is advisable to install it with the bypass as they suggest; due the uv bulb renewable is an annual event. The price using Amazon

was the best.

Save 52% Off

Our water supply has been contaminated by a flood in Sept. In the past we were able to treat our well with bleach then retest and get a bacteria free result. Not this time. We went to this UV system and that cured our problem.

Aqua-Pure AP802 Water Filter System Save 50% Off

Aqua-Pure AP802 Water Filter System, Whole House, 45 gpm
  • High-capacity whole-house water filter provides flow rate of up to 45 gallons per minute (170.3 liters per minute)
  • Reduces particulate, rust, and the taste and odor of chlorine, helps improve the quality of cloudy, colored, or musty water
  • Pressure-relief button makes water filter change-outs simple
  • All Aqua-Pure AP802 filter parts are manufactured from FDA CFR-21 compliant materials
  • Provides filtered water at less cost than bottled water

We''ve been using Brita pitcher for years, but we knew we wanted a whole house filter for three main reasons: (1) drinking water any time from the tap and not have to wait for the Brita to refill, (2) remove chlorine from shower and bath water, and (3) remove the sediments and "crud" from our water. Ultimately it was point 3 that pushed us over the edge when city water kept clogging up your kitchen faucet and it got too tedious to get under the sink and fix the faucet one more time.

We knew we didn''t want a water softener: we wanted to get the crud out of our water, not add more stuff in. What we wanted was a filter: get the chlorine taste out and the crud out.

We did a lot of research, and considered some of the expensive brands like the LifeSource water filter. But in addition to the cost, none of the independent research I found online indicated that they were anything but hocus pocus. Plus, I think we''re talking about $2k or $3k for the filter. After looking into it, it really sounded like marketing hoo-haa with no science behind it, so we dug deeper.

We opted for this one and have been very satisfied.

Ultimately, though, this product is just the filter container that you hook up to the water system. The filter cartridge is a separate product and determines what you will filter out of your water.

This Aqua-Pure system lets you choose between

particulate-only removal ( Aqua-Pure AP810-2 (AP802-1.5-C) Replacement Cartridge, 5 Micron Rating Water Filter )

particulate and chlorine removal: Aqua-Pure AP817-2 Water Filter Replacement Cartridge, 25 Micron Rating .

We went with the latter, and it''s been great. We have to change the filter cartridge every 6 to 12 months, but at $50/pop, that''s acceptable.

The Aqua-Pure system is inexpensive. It was originally made by a company called Cuno which got bought by 3M. We''ve been very pleased with 3M products in the past, so we had confidence of the brand. And so far, it''s been everything we hoped for. The water tastes great, and there''s no chlorine smell, and no more clogging up of our faucets.

The filter system is fairly small, so we just had it installed on the side of the house, in a convenient location to swap out filter cartridges. If you live in a cold climate, I would recommend putting it indoors to protect it from the weather. We are in California, so the side of the house is fine.

The real expense is the installation that really needs to be done by a plumber. Depending how much new copper pipe you''ll need (based on where you are installing it with respect to your water supply), it could run from a couple of hundred dollars in installation to over a thousand. Still, totally worth it. We are very glad we did it.

Buy Aqua-Pure AP802 Water Filter System Now

still has a bit of chlorine taste but still well worth the effort of buying and installing. much better than a brita also

Blueair 400 Series Replacement Particle Filter

Blueair 400 Series Replacement Particle Filter for the 400 Series Air PurifiersI was surprised and not happy when I first looked into air purifiers and found the one recommended most often --Blueair--used filters that cost about $50 and had to be replaced every 6 months. That was a few years ago. Since then, I have not begrudged one dime of what I have spent for replacement filters. I have pets that shed, I live in Manhattan on a street that has been worked on constantly, creating lots of airborne dirt, and my building was repointed a couple years ago, providing more of the same. And I have allergies.

But I sleep well every night and wake up without a stuffy nose. These filters work, and so does the purifier-as well as the day I first turned it on. So far it has outlived both the clock radio and a tower fan.

Like the other reviewer, I was a bit taken back by the $50 price of a filter that is supposed to be replaced every 6 months. But I bought the BlueAir 402 anyway.

This is one of those products that truly works! No false hype, no bogus claims. Since I don''t have pets, and nobody smokes in my home, I have found that I can get a year out of a filter without a problem. At the same time, I am impressed at how well this filter performs. The intake side of my 402 air purifier gets dusty the filter does show a darkening over time and the outlet screen of the purifier has *never* needed cleaned. That says a lot about the effectiveness of this filter.

There may be cheaper, and there are systems that use multiple pre-filters to extend the filter life, but there are no better. If you are considering a BlueAir 402 or other model, don''t let the price of this filter turn you away. You ARE getting what you pay for.

Buy Blueair 400 Series Replacement Particle Filter Now

If you use the Blueair 402 Air Purifier for your office or bedroom, it truly is best if you change the filters every six months. It helps to write the date of the installation of the filter on the side facing you when you open the door of the unit so you know exactly when you put it in.

We found the best prices for replacement filters on Amazon.com. In the marketplace, they range from $[..] to $[..] each. Often, if you buy two or more, you get a good price break. They don''t go "bad", so the pricing can make a difference on a per unit cost if you stock up on them in volume.

It''s also good to clean the back metal screen on the unit ever other month. Turn off the unit, and clean upwards with a damp sponge until all the accumulated dust and dirt is removed. Let the screen dry and then turn on the unit again.

We find the 402 a great filter that makes no noise and does the job well.

Read Best Reviews of Blueair 400 Series Replacement Particle Filter Here

I installed this filter in our BlueAir 403 in just two minutes. After removing the old filter and vacuuming out the interior per instructions I slid this new filter in the slot, aligning the arrows as directed. It is a snug, perfect fit which allows for maximum filter efficiency. Although not inexpensive, this filter, and the system in total has vastly improved the air quality in our bedroom. The plastic-wrapped filter was packaged in a rigid cardboard box which was then placed in a large shipping box; there was not a wrinkle in it. BlueAir filters are advertised to be environmentally friendly, decomposing into carbon dioxide and water which was a plus.

Want Blueair 400 Series Replacement Particle Filter Discount?

This filter is great and doesnt give you Pneumonia like the Ionic Breeze does. The amount of dust is tremendously reduced and helps my allergies.

Capresso 10-Cup Coffee/Cappuccino Makers Save 20% Off

Capresso 10-Cup Coffee/Cappuccino Maker, BlackAfter spending a few weeks researching various coffee makers and reading numerous reviews and online user reports, I settled on the Capresso CoffeeTEC due to its features and the theory behind how it brews coffee reduced aeration to hold flavor (vacuum sealed carafe), no burner to bake the bean and increase acidity, and 190+ degree water dispensed into the brewing basket, which is very hot for a coffee maker!

I have to admit, I was nervous. I saw two general complaints that were common from online user reports. 1) The carafe did not maintain the water temperature, and 2) the frother ceased to work. A few comments on these:

Thermal carafe: I have no clue how anyone can be having a problem with this carafe, unless there''s a problem with the heat of the water entering the carafe or in how they''re storing the coffee after it brews (like, in the refrigerator, perhaps).

I did some tests on the carafe after getting my CoffeeTEC. The carafe was at room temperature (not pre-heated, as some suggest) when doing this test. Immediately after brewing straight water with the carafe in the closed position, I measured the water temperature at 189.3f using a digital thermometer. I closed the carafe and let it sit for exactly one hour then measured the water at 182.1f, a drop of only about 7f, which is fantastic! Now, I also brewed a full pot of straight water on my now-replaced Mr. Coffee, which sat on a hot burner during the brew process. After brewing, the water temperature was exactly 178f. So, after one hour in the thermal carafe with no burner contact, the Capresso water was hotter than the Mr. Coffee immediately after brewing. Very impressive results!

Frothing problem: I have noticed that the plastic pieces that connect the milk container to the frother do have to be sealed properly for frothing to work. Also, it is necessary to clean the items after frothing; a very simple and quick process. Occasionally my unit will not froth immediately even though the steam would blast in an attempt to froth. This has been very easy to solve. After turning the steam on, I simply press the milk container tightly against the plastic piece that connects it to the frothing nipple. Don''t worry if you don''t understand this description. You have to own the unit to know the pieces I''m discussing. Just understand that with some minor manual jostling, the milk will flow and froth wonderfully!

Now, as for my assessment of this coffee maker... it is the best coffee maker I have ever owned! I''m knocked-out by the quality of brew I''m getting. Just as good if not better than commercial coffee houses, because I can make it to my specifications!

A few comments on this though... it took a few weeks for me to figure out exactly how to use this coffee maker so it brews to my liking. When I brewed my first cup, I didn''t care for it. Keep in mind, this unit brews water quickly through the grind. It extracts flavor and aroma through heat, not prolonged water contact with the bean. As a result, you will have to use more coffee than most coffee makers.

As an example, I used to measure one rounded tablespoon of beans (pre-ground) for every two 5oz cups, then I''d add one extra tablespoon for added body. So, for 20oz of coffee, I''d use three tablespoons of beans. With this coffee maker, I''ve learned I need to use one tablespoon for each 5oz cup plus one extra for added body. So, for the same 20oz pot of coffee, I use five tablespoons of beans.

Also, the other detail I discovered is, it was necessary to grind the beans finer than I had before. I''ve started grinding the beans on the Espresso setting of my grinder rather than the automatic drip setting. This made a huge difference on the strength and flavor of the coffee.

So, keep in mind you''ll want to play with the quantity and fineness of grind. If you use canned grinds, you have much less leeway. You''ll just have to add much more grind, but be careful! Don''t add too much or it will overflow the basket. Always adhere to the maximum grind amount Capresso recommends in the documentation.

The coffee maker comes with a gold filter. You may or may not like using the filter; I elected not to use it. The gold filter allows more oil and particulates into the coffee. Some like this; others don''t. It makes for an oilier, cloudier brew. Using paper filters, more of the fine particles are filtered out and much of the oil is kept from leaching into the carafe. The coffee is cleaner, clearer and not murky. I prefer using paper, but the preference is highly individualistic. I''d suggest running some tests and decide for yourself.

In the end, I find the coffee to be superb! This coffee maker is a fine-tuned piece of equipment that responds to the subtlest of changes you impart on the brewing process. Change the fineness of the grind or the quantity of beans used and you''ll experience a noticeable difference in the outcome of the brew. After I determined the right balance that suits my pallet, all I can say is, "Wow!" The flavor and body is nutty, winy and full, the aftertaste smooth and non-acidic, and the aroma outstanding! I highly recommend this coffee maker.

But, plan to make a number of pots when you first get it with the understanding that many of those pots will probably go down the drain. It''ll take some test runs to determine the quantity of coffee you''ll want to use, the fineness of grind, and which filter to use. With due diligence, you''ll have a splendid coffee maker from which you''ll enjoy each day''s coffee for years to come, custom made specifically towards your taste.

So, read the other reviews for what they are and keep in mind some of my comments. In my experience, many of the complaints reflect a user who hasn''t experimented with the grind quantity and fineness, and hasn''t been adventurous enough to work the "piping" when frothing.

I''ve been impressed with the well-thought out products coming from this relatively small company in the small appliance industry. Their Swiss designers have the leading edge technology in coffee makers and the CoffeeTEC is the latest innovation. Coffee is brewed 10 cups in under 8 minutes, and that''s fast. The idea is to have the fresh coffee exposed to hot water for the minimum amount of time, so flavor is extracted without extracting the bitter parts of coffee flavor. CoffeeTEC does this really well. A special 3-5 cup brewing selector makes it possible to brew a perfect small pot of coffee. The coffee goes directly into a stainless steel vacuum carafe, and after removing and sealing the pot the coffee stays hot for hours but never gets heated over and over again as in a traditional hot plate coffee maker. The Auto Cappuccino feature is a genuine plus for those of us who want some frothy milk with our coffee, it turns cold milk into hot milk and froth in seconds. Since all the works are outside of the coffee maker, it''s easy to clean and to remove the milk container for refrigerator storage. This is a winner in the category of latest coffee technology.

Buy Capresso 10-Cup Coffee/Cappuccino Makers Now

This is the second review I have written for this product (Please see the review directly below this one by "bookdeep"). I am pleased to report that we now LOVE this machine, ever since we discovered the "trick," and I am writing again to try and rectify the embarrasingly harsh review that I sent before. As I said in the first review, the coffee machine works fine: it makes a great cup of coffee quickly and efficiently, and it is easy to clean. Initially, we had some difficulty with the frothing mechanism; however, the solution turned out to be very simple. In order to start the steaming/frothing mechanism, there is a large dial that must be turned one-quarter turn from "Twelve O''Clock" (Steam Off) to "Three O''Clock" (Steam On). We discovered that when you turn the dial to the Steam On position you have to bear down on the dial a tiny, tiny bit: maybe the dial would actually go to 3:01 on the clock face, maybe even less. When we do that, the frothing starts immediately, every time. It seems that our trouble was that we were a little too delicate turning the dial. Note that this "overturning" is very slight: we wouldn''t want anyone to damage the machine. I wish that I could take back the previous review because that low rating will have an affect on the average for this product, but I cannot. I hope that writing to correct our error will help others who may consider this machine. Please note, that in spite of the brand name "Capresso" this is not an Espresso machine; it is a coffee maker with a frothing mechanism, which works amazingly well now that we know the trick. If this is the combination that you are looking for, then we cannot recommend this machine highly enough--it does do both of these jobs very well. And now that you know the trick, maybe there will be fewer frustrated, and more happy, coffee drinkers like us.

Read Best Reviews of Capresso 10-Cup Coffee/Cappuccino Makers Here

This is a fine, easy to use, machine that I''m really enjoying having in my kitchen. I had never used a milk-steamer before, and found the idea a little intimidating. But the process is really quite painless, and now I''m wondering why I did without it so long (even my java-phobic bride is enjoying homemade hot chocolate thanks to the steamer).

Anyone who enjoys having a pot of coffee on-call throughout a morning should avoid glass pots like a cliché and instead use a thermal carafe like this one. Not only does it keep coffee steaming hot without constant re-heating, but the wide top and easy-off lid make for easy clean up when you''re done.

The coffeemaker is elegantly designed, seems relatively sturdy, and looks nice on a countertop. Plus, it''s fast, fairly quiet, and -as I said -easy to clean.

For someone like me who just wants to enjoy coffee without trying to become a home barista (''professional maker of complex espresso drinks''), this is as much machine as I think I''ll need ... at least until the one with the built-in burr grinder arrives.

Want Capresso 10-Cup Coffee/Cappuccino Makers Discount?

It makes the best coffee I''ve ever had. The carafe works perfectly and keeps the coffee hot, and at nearly peak flavor, for hours. Those few reviewers who say that it doesn''t keep the coffee hot simply have a carafe with a broken vaccuum seal.

I''m bothering to write a review because I had a problem with the machine, as some others have: the steamer stopped working properly, and the water tank was leaking. But at that point my experience was totally different from that of other posters who have complained about problems with the equipment and Capresso customer service. Get this: we had no warranty information on the machine, having received it 2nd-hand. Still, when my wife called their customer service, with no questions asked we were sent a pre-paid UPS label to return the unit. I put it in a UPS box on a Monday morning. On Wednesday afternoon---two days later---I received a new machine via UPS. (I know that they first received the machine I sent before sending the replacement because they replaced exactly what I sent, no more, no less; i.e., I sent the machine with just the water tank, none of the other parts, and I got back just a machine with a water tank.) I''m as pleasantly astonished by UPS getting it back and forth so quickly as am by Capresso simply and immediately fixing the problem at no charge.

Maybe Capresso "got the message" about customer service and made some changes. I could be bothered that the machine developed problems in the first place, but hey, things break. The bottom line for me is that it makes PERFECT coffee and, when there was a problem, Capresso took care of it astonishingly well.

Save 20% Off

Jura Impressa Z7 One-Touch Automatic Coffee Center Save 3% Off

Jura Impressa Z7 One-Touch Automatic Coffee CenterI previously owned the S8 for about 7 years and after it broke, I decided to upgrade. I love the way Jura will repair a broken super automatic for 275.00 including round trip shipping no matter what the problem but I still wanted a newer model. I did a great deal of research on superautomatics and even bought a Saeco Xelsis. Unfortunately I had to return it as the latte temp never got above 120 degrees despite calling Saeco and working with their support line. I then bought a Jura Z7 as the manual stated that the milk could be heated up to 159 degrees and the espresso/ coffee up to 197 degrees. I love hot coffee/latte. After trying out the Xelsis, I wanted to buy a sure thing that I knew would make me happy. However, the milk at first came out about 130-140 degrees. It took three calls to Jura to figure out how to get the milk to the temp to what they advertise. One helpful person told me to pinch the tubing exiting the milk container before it enters the machine. This slows the stream of milk and increases its exposure to the heating elements but who wants to spend 3 grand on a machine and have to jury with it to get the milk hot enough. Finally, I was told of two things to do to get the milk temp up and how to keep the temp up in the cup. First, when putting the empty cup under the cappucino spout, press the milk button while the cappucino dial is set on steam water. This will spray very hot steam out of the cappucino spout into the cup. This heats up the tubing in the machine and heats up the cup. The third and most important thing is to align the notch in the cappucino spout dial on the border between the steam water icon and the steam milk icon. After flow begins, turn the dial counter-clockwise until the notch is actually into the steam water section but not so far that it stops the milk flow. By doing this I was able to get my milk temps up to the 180s (checking the temps as the milk exits the spout and before it hits the cup). NOW, I could not be happier with the taste AND and the temp of my lattes. Go Jura!!!

I don''t write many reviews, but just this week, we decided to call it quits with our 4 year old Jura, which was about as expensive as the one Amazon is selling. During long stretches, the coffee was great, as was the frother. But during the 4 years, we had to ship it back to Jura for repairs 5 times, and every time, it was for the same problem. According to Jura''s customer service agent, "an air bubble gets trapped in the line and the machine must be disassembled to fix it." Last time, I got pretty annoyed, and the service guy told me quietly that lots of machines have to be serviced more than once for the same reason..For Hello? How about manufacturing a new part, or finding some other way to deal with this design defect? Nope. Instead, it was better for them to keep fixing the machines. After the warranty ended, the cost of the repair, plus professional packing, shipping and insurance was about $300 each trip,

Jura makes beautiful machines, but I"m not going to buy another one. The company doesn''t care about its customers once they get your money.

Buy Jura Impressa Z7 One-Touch Automatic Coffee Center Now

Bought this capuccino maker about 7 months ago, so we know it well. The initial rationale was that we would save 8 dollars a day and countless wait time both of us stopping at starbucks every day. That has happened. I have been to starbucks twice since I bought this. It makes a pretty good cappuccino, I would say is on par with starbucks, my gold standard. The coffee setting tastes different, since it is really a cup of watered down espresso, but you aren''t buying this to brew coffee.

In spite of having the tallest spout on the market (at least at the time of my purchase), I still cannot fit my travel mug under it. You know the stainless steel, 16 oz mug you would want to fill up giving you a vente latte on the way out the door. Maybe they dont use these travel mugs in Switzerland, but we all do here... (In fact, I had to build my own wooden holder that holds a tilted travel mug under the spout.)

Well not only does the standard version of such mug not actually fit, (most are about .5 to 1 cm off), it brings up my second point, its almost hot enough. Well if you have prewarmed your cup in the microwave, and sat down to sip you cappuccino right then, the temperature will be a barely "ok". But if you are used to ordering your starbucks extra hot, your definately going to be found wanting. And if you have to dispense your drink into a cup, and then transfer your drink to your tall travel mug because it wont fit, your really going to be dissapointed in the temperature.

A few other gripes: the thing will only stay on 2 hours, IE it will always turn off, kudos to their green power saving. Problem is, it takes a solid 3 minutes or so to warm up. Then each type of drink you make only contains one shot of espresso. If you want 8 oz of milk with three shots of espresso, you have to turn it on, stand there for 3 minutes for it warm up, then push a button to put an 8 oz cappuccino in, wait another 2 or 3 minutes, then push the button for another shot of espresso, another 1-2 min, then push for another shot of espresso in, another 1-2 moinutes. Does that sound "one touch" to you? For me, it is stading next to a machine for 10 minutes, which is exactly what I am supposed to not have to do. (Not to mention, in the middle of all this you might run out of water, need to empty the tray, or add beans. The chances of one of these lottery wins in your 3 button oddessey are probably 25%)

What this machine needs are:

Taller spout

The milk needs a temperature setting, its not hot enough for me.

The machine needs a timer, so it can turn on in the morning and warm up.

Programmable drinks with multiple shots.

Larger bean bin, it probly cooks up only a dozen shots or so per bin.

For three grand, these things should be a given!

Read Best Reviews of Jura Impressa Z7 One-Touch Automatic Coffee Center Here

There are so many problems with this product I scarcely know where to start. The first sign of trouble is the manual: it is all but incomprehensible and only describes some of the maintenance required to keep the unit functioning. In other words, after diligently completing all the maintenance requested by the manual, the unit would still break down every couple of months; when I''d call customer service, I''d learn that far more maintenance is needed if you want to keep the unit functioning for long. Unfortunately, experience has taught me that even the most extensive maintenance will only delay but not prevent the unit from breaking down.

The need for endless maintenance is annoying since the main advantage of the unit is its ostensible convenience: in other words, it is true that you can make a cappuccino with one touch -but what they don''t tell you is that after that one touch you''ll need to complete half a dozen or a dozen steps before making another one. This obviously isn''t very convenient, nor is it inexpensive: I''ve spent countless hours and hundreds of dollars on cleaning fluids, cleaning tablets, filters, and decalcifying tablets in an attempt to keep it functioning, but all this has only delayed the inevitable breakdown.

And this is where things get ugly: after the unit failed completely recently, I contacted Capresso and was told I could get the unit repaired for a $300 fee. I sent the unit in, and to their credit, it was returned promptly; unfortunately, I could see no evidence that the unit had actually been repaired: when I started it up and filled it with water, the unit proceeded to dump the water all over the counter. I thus contacted Capresso and asked them to send out shipping labels so I could return the unit and have them correct the repair. I received no response. After waiting three business days, I asked again; still no response. After waiting three more days, I let them know that I had contacted my credit card and would be refusing the charges until such time as the unit was actually repaired; within the hour I received an email apologizing and letting me know that the customer service manager was out of the office and would return the next day. I thus waited three more days but never heard anything from the customer service manager. I then wrote to the company president asking him to intercede and address the problem: after a month, I still haven''t heard anything from him.

But the extraordinary inability to provide even the most basic level of customer service isn''t my main complaint with the product: my main complaint is that it doesn''t make very good espresso. I say this, not because I consider myself an expert when it comes to evaluating espresso, but because the unit simply does not work with pre-ground espresso. In other words, I''ve tried pre-ground espresso from each and every brand I can find; they all cause the unit to clog and thus leak. Worse, when I called to ask about this, I was told it was "normal" and that I would need to use the grinder instead. At that time, I didn''t realize that if the unit couldn''t process pre-ground espresso, then it presumably wasn''t grinding the beans to the same level of fineness as pre-ground espresso. As a result, what Capresso calls espresso is quite different from what I''m used to: its quite thin and watery and I''ve never found a way to make it any thicker. If you''re a fan of espresso, I''d encourage you to find the unit in a store and see if their version of espresso is to your liking. Of course, this may prove hard to do: Williams-Sonoma no longer carries Capresso products, and I''m not sure if you''ll be able to find anyone who still does. Given my experience with both their customer service and the quality of the products offered by Capresso, I''m sorry to say I simply don''t find this surprising.

Want Jura Impressa Z7 One-Touch Automatic Coffee Center Discount?

We purchased this machine in May 2012 for use in a small office. We probably make 2 or 3 cups of cappuccinos and an espresso each day. The original machine started giving an error message to "add beans" even though the bin was full of beans about 4 weeks after purchase. We were told to remove all the beans and `air out'' the machine because there might be an oil build up (oil from the beans). We scooped out the beans and let it `air out'' over the weekend and it still didn''t work on Monday. I called customer service again and did everything they told me to do but it still didn''t work. So we shipped back the machine and they shipped us a new Z7. After about 4 weeks the 2nd machine stopped making froth for the cappuccino. Customer service told us that it could be the froth dial. We could not use the machine but they sent us a new froth dial and it worked. 8 weeks later, here we go again we''re getting a "add beans" message on the 2nd machine. To make matters worse, even the hot water sprout stopped working so we can''t even make a cup of tea. The machine does nothing. We called Customer Service and were told, AGAIN, to remove all the beans and `air out'' the machine because there might be an oil build up, etc. We scooped out the beans and let it `air out'' over the weekend and it still hasn''t worked for 5 days. This time because we''ve had the machine for over 3 months JURA won''t send a replacement. We have to find a box and ship the 2nd machine back to them. JURA doesn''t even pay for UPS to pick-up the machine they send a receipt but you have to carry the machine to a UPS drop off location. I have a bad back and the machine weights approximately 40 pounds packed this is inconvenient and is a big deal to me. It''s too late to get our money back so we are stuck with the JURA Z7 but we are not pleased with it at all. I would NOT purchase this machine again ever. For $3,000 I expect a machine that works for more than 4 weeks before needing to be repaired. Do not purchase if you want a machine that works.

Save 3% Off

Clover D14A Hot and Cold Point of Use Water Dispenser Save 22% Off

Clover D14A Hot and Cold Point of Use Water Dispenser With Hot Water Control Switchsince we got this, it''s been working really great ! Very happy ! My staff loves using the machine because of the hot and cold water feature. and it matches the other appliances :D

I didn''t buy this on Amazon, but I didn''t save much money by buying it elsewhere. When I installed it, it took forever to fill so I did some investigating and found that the water was barely trickling in. After some testing, I called their Customer Support and reported it. They sent me out a new valve and float assembly and it is working flawlessly. You can''t get the water very cold if you like and the hot water is indeed 185 degrees. Very happy with the purchase after a few weeks.

Buy Clover D14A Hot and Cold Point of Use Water Dispenser Now

Crane Drop Shape Cool Mist Humidifier Save 12% Off

Crane Drop Shape Ultrasonic Cool Mist Humidifier with 2.3 Gallon output per dayI received this humidifier 2 weeks ago after searching for a decent humidifier to replace the one i owned that was famous for robbing me in replacements filter, etc. fees. This thing fits the bill. The design is great, it''s super quiet, and gets the job done. In choosing this product i read all the reviews. The reviews that made me hesitant to purchase this were the complaints that said: a)that the furniture on and around the humidifier got wet all the time, b)that the machine did not cut off if empty, as advertised, c)that the machine is hard to clean, and d) that it makes a lot of noise.

With hesitation, I purchased the product in good faith.

I was immediately pleased by the design. I read the owner''s manual even though i thought it all was a "no brainer". The manual actually explained a)how to adjust the mist as to not wet the furniture around it, and b)that the machine will turn off when empty, but the light on the device will remain lite...obviously the part those that said the machine did not turn off failed to read, and c)how the machine is easy to clean with a vinegar or chlorine solution.

Cleaning is easy. I recommend using the bleach solution as bleach will kill anything..not to mention it also gets rid of the discoloration.

Lastly, the sound the comes from the machine is very subtle, but when u hear it, it is exactly like the soothing sounds of a filter running on a fish tank. It actually helped me sleep... having this white, very subtle noise.

I like this thing. My skin and nose are happy.

I hope this clarifies some of the ambiguity i found in the other reviews....

I purchased the Crane cool mist humidifier in Dec''10 and have used it, with great success, for many months. With all the negative reviews (about 20%) I almost didn''t purchase this machine. But I''m glad I did, because it works really well for what it is: a mid size/capacity humidifier.

First of all: ***this humidifier has a 2.3 gallon per day maximum output, with a .9 gallon tank.*** Amazon''s initial title for this (and many other humidifiers) mentions daily output capacity rather than tank size... this may be confusing, although the correct specs are prominently listed on the Amazon page fifth bullet point in the "product features" section. As for Crane (the manufacturer), their package clearly states a 2.3 gallon daily output, and .9 gallon tank size... The reviewers complaining about the "misleading name" should try emailing Amazon suggesting a title change on their website... instead of writing a 1 or 2 star review of the product. That would be more helpful and more fair.

As for the product itself:

A few buyers obviously received defective machines; this has to be expected on some level with any manufacturer.

But having read over the negative reviews, I realized that most of the complaints were due to improper use of the machine.

It is essential to read the instruction manual and use the machine as intended by design. Doing so will avoid the pitfalls described by most of these 1-2 star review writers. For reference, I have addressed their most common complaints below:

1) White dust buildup in the room: use filtered or distilled water. This is important if you have hard tap water. (85% of American homes do.) I run my tap water through a Brita filter; the exchange ion resin lowers the concentration of calcium carbonates, accordingly softening tap water. It also helps keep the humidifier cleaner by removing organic impurities, and I have had no white dust buildup. ***If your water is particularly high in mineral content, you should use distilled water, or else opt for a vaporizer-type (humidifying) machine, which creates water vapor free of white dust.***

2) Limited effectiveness: you are trying to humidify too large a room. In my 500 square foot living room level the machine helps a little; in my 150 square foot bedroom the machine is more than adequate.

3) Height of machine: the manual directs you to put the humidifier *at least* a few feet off the ground; there''s no reason you can''t place it even higher up if you wish. Doing so will disperse the mist more effectively.

4) Machine runs out of water: try turning it down to about 2/3 power instead of full power. The machine is practically noiseless at this setting and the water tank if actually filled to the rim will last at least 8-10 hours.

5) Machine makes bubbling noise on high: see #4 above.

6) Wet area forms immediately around humidifier: you have the machine turned up too high for the conditions in your room. This is explained in the instruction manual: you need to make sure the mist isn''t falling down onto the surfaces around the machine; otherwise moisture will accumulate on those surfaces. Turn the power dial down until the vapor stream is fully evaporating in the air.

7) Machine leaks: Take care that the water tank fits snugly into place, with no gaps. Also, make sure you have the clear rubber ring that fits inside the tank cap. During my initial setup, this little (1 1/2" diameter) ring came loose and rolled away, and I almost didn''t notice. The ring ensures a tight seal on your water tank cap; without it, I''m pretty sure the machine would leak.

8) Machine gets moldy: you are not following the correct cleaning routine, as described in the manual. You need to empty and rinse out the tank daily, and empty the bottom part of the unit too. Once a week you should use a white vinegar/warm water mixture in the tank and bottom of unit (see manual).

I hope this was helpful. If my humidifier breaks down I will certainly update this review.

Buy Crane Drop Shape Cool Mist Humidifier Now

We bought the Vicks cool mist humidifier first. it was so noisy in the nursery that we didn''t use it when our daughter was sleeping. We bought this one hoping that it would be a little more quite. We can''t even hear it! It also takes up very little space and is easy to fill in the shallow bathroom sink. Awesome purchase. worth the extra $.

Read Best Reviews of Crane Drop Shape Cool Mist Humidifier Here

This humidifier is the perfect size for a bedroom. The tank empties in about a day, so the water doesn''t sit around too long to get mildew or mold. The humidifier puts out lots of moisture, and is absolutely whisper-quiet! We have the penguin-shaped one for our son''s room, and this one for ours. Both are great.

Want Crane Drop Shape Cool Mist Humidifier Discount?

We bought this humidifier for the bedroom because we were waking up every morning with dry, cracked lips and sore throats and sinus due to the very dry air in the house during the winter. This unit pretty much solved the problem for us.

Pros:

Very quiet. I imagine if you set it next to the bed you could hear it, but we set it across the room and the only thing I hear is the occasional bubbling as it takes in more water.

Easily adjustable. The knob on the front that controls flow is infinitely adjustable, so you can get just the flow you want.

Easy to fill. Just take off the reservoir and fill from the sink.

Puts out enough moisture to humidify a fairly large room. Our bedroom is 16 by 20 feet, plus a master bath, and it makes a big difference in the humidity of the rooms.

Cons:

It doesn''t seem to automatically turn off when it runs out of water like the description says. Maybe ours is broken and maybe not, but it doesn''t turn off. No big deal except the wasted energy (which can''t be much) but I wish it did shut down.

I wish the reservoir was bigger. The size it is makes it easy to take and fill, but you pretty much have to fill it every single day. It''s a trade-off, but I would have preferred something twice the size that was a bit more difficult to fill due to size.

Save 12% Off

Sprite SLC Replacement Slim Line Shower Filter Cartridge Save 45% Off

Sprite SLC Replacement Slim Line Shower Filter Cartridge
  • Chlorgon and KDF media helps prevent dry skin and damaged hair by reducing total chlorine
  • Improves the quality of your shower water by reducing chlorine odor, dirt, and sediment
  • Quick and easy cartridge change does not require any tools
  • For optimal performance be sure to change the filter once every 6 months

The shower filter does an excellent job of removing the chlorine (they use a lot where I live)and the lime.

Buy Sprite SLC Replacement Slim Line Shower Filter Cartridge Now

I also really like having this filter on my shower. I can definitely tell a difference, not only with the lack of chlorine odor, but also in my skin not drying out as much. The slim design is nice, too. Also, KDF won''t destabilize in hot water like charcoal will, which is nice to know when you''re in the mood for a hot shower.

Read Best Reviews of Sprite SLC Replacement Slim Line Shower Filter Cartridge Here

My local stores stopped carrying this filter lately, so I was so happy to find it even less expensive online.

Want Sprite SLC Replacement Slim Line Shower Filter Cartridge Discount?

Does remove chlorine very good,,,,great I would recomend product since its not exspensive, Does remove chlorine very good,,,,great I would recomend product since its not exspensive

Eureka DCF-21 Filter

Eureka DCF-21 Filter; Long-Life WASHABLE, REUSABLE and Allergen Filtration, Compare With Eureka DCF21 Part # 67821, 68931, 68931A, EF91, EF-91, EF-91B; Designed & Engineered By Crucial VacuumThis filter was a great replacement. It fit well and works great. Now I can thouroughly wash and dry the unit that came with the vacuum and switch them out. Price was right too.

I agree with William C. Spaulding, Oct 24, 2012 review. Filter does not lock into canister head/dust cup. However William was wrong when he said tabs are too short, it is the gasket on the end that is too thin. The gasket is half the thickness it should be, therefore, does not "push" tabs into the locking notch. The gasket acts like a "spring" locking filter into notches which also seals the filter to the head.

I do design for a living, but this is just such a blatant change that effects fit and function. This would have never happened at where I work and if it did, we would not ship out the part until it was corrected or returned to the vendor. Someone at the manufacturer was trying to save a penny (or less) a filter and turned it into a unusable piece of trash. They could apply a second gasket onto the first to build it up to the correct thickness.

I will not put tape on the tabs because the gasket seal is very important to the performance of the vacuum. Crucial Vacuum needs to stop selling these, refund or replace the "defective" filters with "good" filters free of charge. Then Crucial has to get the supplier to correct the defective gasket or return them to P.R.O.C. (People''s Republic Of China), YUP, made in China.

I felt good about buying from Crucial Vacuum because, in the past, I purchased allergen vacuum bags from Crucial. This has left a really bad taste in my mouth in trusting this brand again. When I put in a request to return the item, they expect me to pay the return shipping! I sent them a message requesting a prepaid return label or just refund purchase price. I will update this review, on how Crucial vacuum handles this whole mess.

Update 30 October. Crucial Vacuum is issuing a refund. But never mentioned if they were going to correct the filter thickness issue which can be remedied by attaching another gasket over the existing gasket to "build up" the gasket to the correct thickness. Raised stars to 2 because they issued a refund immediately.

Buy Eureka DCF-21 Filter Now

I ordered this filter along with another one needed for my Eureka AS1000 vacuum.. I was a little worried that maybe they would be cheaply made because they are literally HALF the cost ''here'' VS the store prices ''BUT I am happy to say that they are not a cheap knockoff and they fit perfectly (actually a bit better)!! I will defiantly be ordering these filters anytime I need to replace them!! -I defiantly recommend!

Read Best Reviews of Eureka DCF-21 Filter Here

This filter is an exact replacement for the one in my vacuum. Arrived on time and in perfect shape. I am going to get another one so I can wash one while using the other.

Want Eureka DCF-21 Filter Discount?

This filter works well and is easily washable. However, the 3 projections that are slid into slots to hold the filter in place are too small for the slots. Hence, the filter falls out while vacuuming, allowing the dust to go straight to the motor. I have improvised a solution by taping small pieces of duct tape over the projections to make a tighter fit, but it would be nice if the projections fit snugly in the slots, as the filter from the original manufacturer does. Otherwise, I would definitely give this filter a 5-star rating.

Counter Top Water Filter System Save 39% Off

Counter Top Water Filter SystemReceived my new countertop water filter in timely fashion and it NOW works well. I had to go to Home Depot to purchase a faucet adaptor ($5.00) as none is included with the product...even though it clearly states it is included. The supplier''s response was basically...it''s your responsibility. The screw on fitting supplied has a female thread while every kitchen faucet I ever owned requires a male thread to attach where the aerator is. The posted ad on Amazon also says 1 Micron filter included, again not so, packing slip says "Filters Sold Seperately" and I was charged an additional $10.89. Also an extra $.79 for a plastic wrench to open the filter. The unit works very well, removing any processed water "smells". A definite plus for a city boy (Philly) looking to ditch the bottled water habit!

Save 39% Off

Whirlpool 2260502B Water Filter Cap for Refrigerator Save 38% Off

Whirlpool 2260502B Water Filter Cap for Refrigerator
  • Works with the following models: Maytag 10654782803, Maytag 10654783803, Maytag 10654784803
  • Works with model: Whirlpool ED2DHEXWB00
  • Works with model: Whirlpool ED2DHEXWB
  • Works with model: Maytag 10654793803, Maytag 10654792803
  • Genuine Replacement Part

Works fine, but I''m not sure why it''s so expensive. It''s molded plastic and comes without any fancy packaging (just a plastic bag). The used fridge we bought was missing this part so we had to replace it to get filtered water...someone is making out like a bandit!

Buy Whirlpool 2260502B Water Filter Cap for Refrigerator Now

Fit the filter and fridge and it works. Only problem is that they did not offer it in the color of my fridge trim (Grey), but the black doesn''t look too bad.

Read Best Reviews of Whirlpool 2260502B Water Filter Cap for Refrigerator Here

This filter was perfect for the fridge. It was exactly what I needed and very inexpensive. The product arrived earlier that expected

Want Whirlpool 2260502B Water Filter Cap for Refrigerator Discount?

I mistakenly threw out my oriiginal cap when replacing the filters. Bought this one based on the part number from the fridge''s manual, and this is perfect.

Bissell Steam Mop Hard-Floor Cleaner, Green Tea Save 39% Off

Bissell Steam Mop Hard-Floor Cleaner, Green Tea, 1867-7I live in a neighborhood where EVERY home is "green built certified" this means that, to have that certification, the builder built no homes with carpet. All the main floors are polished concrete and the upper floors wood. The bathrooms all have tile and/or slate in every home.

Because of this, as you could imagine, steam mops are quite the neccessity...not only because they get the hard surfaces better than anything else, but because they are also "green" and clean chemical free. I''ll be honest, for us...that''s a bonus but we weren''t cleaning chemical free before. We like chemical free for our pet''s paws but I''ll confess I was mopping with chemicals before I got my steamer and just kept the pets out of the room while doing it because, up until then, I couldn''t get it clean any other way.

Okay, so that said...we decided to have a steamer show down to compare 5 different steamers because my friends and I knew as long as we are in these homes we are gonna have to have a steamer to get all these hard floors clean...we may as well figure out which one to buy next go round. Because my own home is graced with 2 cats, 3 dogs, and two gregarious cooks, my kitchen floor (which had not ever been cleaned by a steamer since my steamer had just arrived) was the testing spot.

Mind you, I vaccuum twice per week and do a mega mop twice a week. I THOUGHT I had pretty clean floors in spite of my pet capacity.

I thought wrong. These picked up dirt so well it''s scary

So here''s the results:

1. steam mops are the mac daddys of clean floors. What these things picked up was tremendous and no comparison to my vigorous prior constant major mopping.

2. So now I''ll break down the elements of each mop we used and then go into more detail about each at the end.

We tried out:

"S": The shark by Europro

"E" The Envirosteamer by Eureka

"H" the haan steamer

"M" the Monster

"B" The Bissell Green Tea

CORD LENGTH: so you don''t have to stop and unplug and replug in somewhere else:

Shark ( will be referred to as S):20 feet

Envirosteamer (will be referred to as E): 25 feet

Haan: (will be referred to as H)19''8"

Monster (will be referred to as M): 25 feet

Bissell (will be referred to as B) 17 feet

STEAM TEMPERATURE: this is a primary element. The hotter the steam, the more dirt picked up and hot steam will also kill parasites, mold and mildew and loosen more dirt:

S 110 degrees. lame

E 220 degrees. very hot

H 212 degrees. very hot

M 266 degrees. hottest...although the envirosteamer and haan seemed plenty hot enough. The shark didn''t clean nearly as well and this was one reason. 110 degrees just isn''t going to melt off stuck on grime.

B 125 degrees. Note that, because of this low steam temperature the manual said that if I wanted to sanitize the floor or pick up caked on spills, I had to "hold the steamer on the spot for 15 seconds but no more than 20 because that could damage some floors". Now I don''t know about you, but if I can sanitize with one swipe of the other steamers because of their sanitizing temps my floor will be done WAY faster...and I also don''t have to carry a timer to worry about the extra 5 seconds where my wood floors could get damaged when I have to hold the Bissell for 15 seconds on my wood but no more than 20! My sink water is hotter than the Bissell so it would take less time to use a regular mop if I have to hold the steamer on every spot of my floor for 15 seconds to sanitize. Just sayin

BUILD:

We found how it was made corresponded with issues with the steamer. The Shark, for example, was quite flimsy and they actually sell replacement handle kits because so many people have issues with the handle breaking! We know this because my neighbor''s shark broke and the store had a replacement handle kit on the shelf because he said "it happens often". That''s an extra cost.

Envirosteamer: Was 5.4 lbs which made it lightweight but strong enough that you didn''t have to press down to clean. Very well made and strong parts

Haan: not made as well as the envirosteamer but it''s more expensive so this was a surprise. A bit flimsy and you need to press down on it more to clean at 3.15 lbs.

Monster: hefty and well made at 9 lbs but a bit too heavy unless you want a good workout. (Note: They have changed the Monster handles on the mops now and they are all plastic and people are having breakage issues)

Bissell: It''s 8.4 pounds but that includes a water filter that you have to get for this one (see notes below)

WATER CAPACITY: Very important because having to stop and add more water just adds on to the time you have to spend cleaning, especially if you are cleaning a hallway or livingroom or some other area that has no sink:

S: only holds 10 oz of water. Lasted for 10 miinutes of cleaning

E: holds 20 oz. of water. Lasted for over 20 minutes of cleaning (we stopped at 20 and it was still going)

H: holds 11.83 oz of water. Lasted for 13 minutes of cleaning

M: holds 17 oz. of water. Lasted for 15 minutes of cleaning

B: holds 13 oz of water, lasted for 12.5 minutes of cleaning AND you have to undo and remove the tank from the machine every time you fill it up then hook it back on and the steam tank is on the handle rather than the base so the steam doesn''t flow directly out after heating up which may explain why it''s not as hot once it leaves the machine. The way this mop is made the water flows past heating elements which can, according to Bissell, develop calcium deposits on it so this is the only mop where, because of this, you also have to use a water filter with it and replace the water filter when there is build up which means an extra 12 bucks every few months. The better mops are made to heat the water in a metal tank so this is not an issue and you pour the water directly into the tank.

STEAM HOLES: We found a difference although you''d think they''d all be the same. The shark and Bissell only had one hole that the steam came out of so it wasn''t cleaning things on the edges, just in one spot. All the others had steam coming from bottom and sides.

SIZE: The taller it is the less stooping, the wider the mop head, the more it covers

S: 40"Hx12"Wx7"D. Apparently built only for the height of a small child to push unless you want to bend over and push.

E: 50"Hx13.25"Wx6.75"D (the fact that this depth was smaller made it reach under applicances better...it fit better under things)

H: 50.5x11.5x7.5

M: 48x12.7.5

B: 45.25H (this was uncomfortably short as well) x11 x8.4 (even though this didn''t fit under cabinets because of the depth it did swivel the best)

Conclusion of comparison: First it must be pointed out that, in order to use the shark and the Bissell, you had to keep pumping the water. This was the most annoying feature of anything...the others just steamed on their own and didn''t wear out your fingers. Hated this feature of the shark and Bissell. We liked that the Monster and the Shark and Envirosteamer and the Bissell came with 2 cleaning pads rather than one. The Haan only came with one at the time of the review (I double checked since when she bought hers it was also only one and as of today, that hasn''t changed) so that ups the price even more because I can''t imagine only wanting one to clean. All worked well on sanitizing mattresses and showers. too.

But the winner picked by all of us unanimously as the mop we want to have for our next steam mop order?

The Eureka Envirosteamer. It picked up the most dirt, was made as well as the Monster but was less expensive, held the most water, emitted the most very hot steam so it sanitized as well and quickly wiped up caked on spills, lasted 3 times as long with one water resevoir fill-up as the others, and had a cord as long as the monster. BUT if you have carpets than I might recommend the Monster because it has a carpet attachment that allows you to steam clean your carpets and it picked up pretty close to the same amount of dirt as the Eureka Envirosteamer, and had close to the same features...a bit heavier though but that may make it last even longer. It is costlier, but to clean 2 surfaces I would think that might make it worth it.

UPDATE: The Haan just started including 2 pads with the mop according to the product description page. Not that this changes our opinion since it didn''t work as well and the parts were flimsier, but it should be noted that this issue of not having enough cleaning pads has now been resolved and is equal to the other mops.

ANOTHER UPDATE: 1. The Shark came out with a new machine that holds more water and has a longer cord BUT it still only heats the water to 110 degrees so it won''t sanitize or get rid of trapped grime at this "bathwater" temperature.

Another update: I haven''t tried it yet but was told about an even better mop than the Eureka Envirosteamer but I can''t personally afford it...still, it''s worth mentioning in case you can. It''s called the Ladybug XL2300 and is a canister steam mop. It heats the water to 298 degrees (woah!) so it''s a super sanitizer but it''s over a thousand bucks. It also comes with 6 towels. I didn''t include it in my review because I haven''t ever tried it and I wanted to only include mops I personally tried but it''s got great enough stats that, even though it''s out of my price range, I thought I''d pass it on as a super sanitizer when I read about it.

Also: Don''t spend money buying extra pads for the Eureka. I was in a pinch and used a kitchen dish towel...the rectangular kind...just clip on both ends. It worked just as good or better...because they are thinner so the steam penetrates faster and therefore reaches the floor hotter. However, I would recommend still only using the thick pads that come with it for your wood floors just to be safe. But the super hot steam penetrating the dish towel worked excellent on tile and hard floors. Also, you can flip both the towel and the pads that come with it on the Eureka to double the usage...when it gets dirty, just flip it over and use the other side. I use several old dish towels with this but I like best the kind that just have a bit of texture but no squares sewn on them...but they all work great. So do the pads.

I''ve owned the older white model for over a year now the old terry pads didn''t bother me as far as shrinking went, but I sure wore holes in them. The new microfiber pads are a nice improvement, easier to get on and off, and appear to be more durable.

I''m a big fan of this product and was very disappointed when Bissell appeared to discontinue it I''ve wanted to purchase one for my mother and mother in law.

So, for the review:

Nothing cleans your floor better than good old fashioned Cinderella-style scrubbing. But given that I have around 1800 square feet of hard flooring, three kids, and four dogs my knees just can''t take that kind of torture cleaning something that is just going to be spilled on, puked on, or smeared with banana in a matter of minutes.

I have tried all the other leading brands of hard floor cleaners, and this one is by far the simplest to use and does a decent enough job that it''s a regular in my household cleaning routine.

Pros:

Uses nothing but water. No chemicals, no expensive solutions. I do purchase distilled since we have hard well water and the filter on my old model hasn''t needed replacing.

Cleans my ceramic tile and bamboo floor quickly and effectively. The water dries very quickly. My tile never looks streaky, but the bamboo flooring does a bit.

Piece of cake clean up. Toss the mop head pad into the laundry, wrap the cord up and you''re done. Small and compact, easy to store.

It''s very quiet. I can clean after my kids are in bed and the soft steaming noise wouldn''t bother even the lightest sleeper.

Cons:

The cord really is too darn short, but I''ve remedied that with an extension cord.

It''s a little short for me. This gripe isn''t very fair because EVERY mop, broom, and vacuum are too short for me (except for the Dyson) I''m tall. But I will mention here that short women aren''t the only people who clean! My 5''10" self and my 6''4" husband both have to hunch over to mop the floor with this. It''d be lovely if the handle could extend.

Doesn''t do a great job on grout but nothing does. I''ve decided I just hate tile and grout period.

It does take some effort to push, but cleans overall more quickly than the Powered Floormate.

Like any machine it can''t get right up close to the walls and though its mophead fits under the cabinets, it simply cannot clean right in the crack where the floor meets. So every so often I have to get down and hand scrub those areas.

----

Highly, highly recommend for regular use. Does a great job at steaming the dried on grime and gunk my kids regularly paste the house with.

----

Update 10/11/2010 the microfiber pads have worn out, but they lasted much longer than the old terry pads, have had to order replacement pads, but no biggie. If you sew, they''d be easy to patch with some microfiber towels.

Still love this thing, it gets used a couple times a week on our very messy floors! We now have hard flooring in the basement too (more bamboo) so it gets used more than ever.

Buy Bissell Steam Mop Hard-Floor Cleaner, Green Tea Now

This product is just OK. For some with lots of tile that not too dirty, it may be fine. It is a light cleaning tool. If I had lots of heavy regular filth due to heavy animal and kid traffic, I wouldn''t buy either steam cleaner. I am returning the Bissell because I have a lot of wood laminate and it leaves the floors WAY too wet and streaked. But you ought to be aware of the pros and cons since some things may not matter to you. I also borrowed my sister''s Shark Steam Mop so I will compare the two for you as the cost is identical.

*The Bissell has a swivel head which is great around the toilet and the Shark does not swivel at all.

*The Bissell is well made for a such a low profile appliance and feels sturdy with a nice thick cord. The Shark feels cheaply made with a flimsy cord. The lengths of the cord are similar. You''ll need to use an extension cord with both.

*The Bissell has a removeable water bottle (convenient!) and the shark does not.

*The Bissell weighs more than the Shark (about 8 pounds), but is very easy to push. The Shark is harder to push, but weighs only 3 pounds. You''d get an aerobic workout if you cleaned a whole house of flooring with the Shark and was a lightweight like me!

*The Bissell leaves you with a VERY wet floor even if you go easy on the steam trigger. I also had lots of streaks on my laminate wood flooring. I would not use it on laminate or wood w/o drying them off ASAP. The Shark does not leave streaks and did not leave a sopping trail behind. The floors dried on their own in under a minute. This is a HUGE plus!

*The Bissell pads have a drawstring and are pretty thin and not absorbant which is a contributing factor to the soppiness the mop leaves behind. The Shark pads are velcro attached (easier!)and are thicker and more absorbant. They are also much more expensive to replace, however.

So, my conclusion is that if I had tile floors, I might consider keeping it as the excess wetness wasn''t as huge streaky issue (I went and cleaned my in-laws white tile with it) and it''s a sturdier product that seems like it will last for years. I would just find some elastic pads that were ALOT better (I was considering the Tersano pads sold here Tersano lotus Wet Mop Cloths, 2-Pack #LMC28 as a possibliity since they will fit). But since the drier steam and the better pads are VERY important to me, I may actaully go with the Shark even though the machine is rather flimsy feeling and appears more cheaply made. I''d just use distilled water in it and hope it goes few years before falling apart. You''d think that by now some manufacturer would be able to provide the best of both products. What happened Bissell? You could have had a GREAT product if the pads were thick and absorbant and you provided us with the dry steam that the infomercials imply!

Read Best Reviews of Bissell Steam Mop Hard-Floor Cleaner, Green Tea Here

Well, it''s a newbie review since the product was just released. Time will tell if I actually use this long term or not...

But so far....

I actually do like it! There are only 8 gazillion options on how to best clean your floor, none which truly compare with getting down on your hands and knees. But, for the TYPICAL user who needs an easier solution to a pretty clean floor a couple times a week and particularly prefers not to use chemicals this actually works quite well. I am not disappointed.

I will make a couple notes though:

I guess I wrongly assumed that since it''s using "steam" water it is going to be sanitizing as it goes along. After reading the manual though it states to actually disinfect an area you have to let it steam in that spot for 15 seconds. Obviously to do a whole floor would take the afternoon. But, okay, if you drop a piece of chicken it''s a nice option I suppose.

Also, I was really hoping it would leave a streak free clean but the floor does end up with a bit of standing water and does leave some streaks. Maybe if you don''t hold down the lever quite so much it would just release less water. Of course, though, then it''s not steaming as much either.

Additionally, the lever is a bit tough to hold down for extended periods of time so not for those users with weak pointer fingers. No biggie though.

The cord is pretty short, so I could see that bothering some people. Although I like short cords. Less opportunities to fall and break my neck.

So, in the product''s favor, it does a decent job which is what I was most concerned about. If I let it steam for 3 seconds or so right over something stuck on the kitchen floor it takes it right off. Also goes under the ledges and stuff nicely. The pads are easy to take on and off and it''s quiet.. Also heats up very quickly (a few seconds) and the water lasts long enough for me to do the whole kitchen and dining room. And it''s heavy enough you don''t feel like you have to bear down on it like you do the Swiffer.

One last thing though. It isn''t a super quick clean, in my opinion. I almost think a mop is a little faster because with this thing you kind of want it to go slower so that it can really steam. So, it isn''t necessarily saving me much time. But it is saving hassle, chemicals, and my back!

For someone who understands that that there are no quick fixes in life and they will never find anything that can replace true blood, sweat and tears of doing the job by hand it would be a good find. It is a nice thing to have and a decent close 2nd.

Want Bissell Steam Mop Hard-Floor Cleaner, Green Tea Discount?

I bought this after much online research and figured it had to be too good to be true. A product that would clean without chemicals, not be hard to use, and not need a million pieces! This mop is very light to move, the pad is easy to clean via wash or sink. I most like how it doesn''t leave streaks. Everything else I''ve used on my sealed hardwood floors leaves streaks. No more on my hands and knees! The only things that are a little pain are that you have to take the pad off the bottom after use so that you don''t leave a wet spot (no different than any other mop), the cord tends to be on the short side, there is no way to turn it off except by unplugging it, and that if you aren''t careful with the amount of steam you will have to go over the flooring with a towel. This is only a problem on the wood, on ceramic it dries without problem. I''ve been on the lookout for a product that is easy and efficient. After having mine for a month I am still happy and would recommend it to anyone. Oh, this is Randall''s wife writing the review.

Save 39% Off

Inline Water Filters 85470 Washing Machine Inline Water Filter

Inline Water Filters 85470 Washing Machine Inline Water FilterI''m on a well and we have a lot of sediment in our water. So much sediment that we have to remove the factory installed screen on our clothes washer twice each time we wash a load of clothes. This is essentially a larger screen (trap), but more accessible and with a fibrous material included (filter). It might be a bit too restrictive for my needs. I like the product, and it''s built well (solid and simple, PVC, easily disassembled/reassembled), but I''m not convinced it''s any better than a pressure washer inline filter (green cap), and those have a more accessible filter if, like me, you need to remove it often.

I''ll update as I use it if I''m able to edit this review.

This device works great. Simple and straight forward to install.I used the white plumber tape on the threads to prevent

any leaks. We have had it for several months ..I''ve checked the filter and it is collecting the fine

dirt incoming from the well that had nearly burned up the washer before we realized we had a problem.

very pleased

Buy Inline Water Filters 85470 Washing Machine Inline Water Filter Now

I have well water, and due to some interaction with water and hot water heater, I get flecks of calcium in the hot water. The washing machine screen would clog frequently, so I decided to try and pre-filter. This unit worked great for a month or so, but the fibrous screen clogged as well. I disassembled the unit and pulled the fiber screen out, leaving just the metal screen, so hoping I can now get several months before clogging.

If I recall, the info for the product does not mention a fiber screen, thus this review. Just be aware of it it may not be an issue for you, and if all you want to do is trap occasional flecks of metal etc this will probably work fine for you.

David

Read Best Reviews of Inline Water Filters 85470 Washing Machine Inline Water Filter Here

Im on well water and this product might be ok if you are also using a whole house water filter, which im not. I do have one on order since this clogs up just as often as the inlet on my washer.I will update if this fixes my problem.

Update.....i now have the whole house filter installed and problem solved. i should have gotten the whole house filter first and i dont think i would have needed this.

Want Inline Water Filters 85470 Washing Machine Inline Water Filter Discount?

I''m trying this filter to see if it can help with well water problems. If you have well water you have sediment. I know it will filter the water the question is HOW LONG BEFORE THE FILTER NEEDS REPLACED? The filters are a bit expensive depending on how many you need in a year. The installation was quick and simple just turn off water and screw on filter. Will report back after I have some months use.

Light My Fire Original Swedish FireSteel Army 12,000 Strike Fire Starter Save 39% Off

Light My Fire Original Swedish FireSteel Army 12,000 Strike Fire Starter - BlackLanyard is plenty long and it makes lots of sparks (after a couple of scrapes to remove the paint). If lanyard was not long enough one could exercise ingenuity and put on a longer cord.

It would easily light propane, but if you try to ignite a piece of sheet paper you will have trouble. Sheet paper is not fine enough and is not proper tinder (though you could shred and rumple it to make good tinder). You need a finer tinder bundle. Paper towel was also unsuccessful. I had easy success with toilet paper and dryer lint. It sparks more if you slow down and increase pressure a little. If the woods are wet and you can find no dry tinder you are in trouble, which is why most people carry tinder or fire starter or pick it up on the trail when they can.

I think it is easier to use the magnesium fire starter with a basic metal jigsaw blade as the magnesium shavings will ignite paper towel easily, and can also ignite paper if you make a dime sized pile of shavings (when igniting paper don''t set the end of the magnesium fire starter on the paper as when you scrape the flint the vibrations will jiggle the shavings all around). Even better than a jigsaw blade may be a short hacksaw blade because it has a good hole you can put the cord through.

In summary: if you carry or can find/make good tinder the Swedish firesteel is tough, simple, and a good product. For normal people who want a firestarter that is somewhat easier to use carry the magnesium. That is what I will carry, in addition to good tinder (cotton balls with vaseline mushed in), and a very good lighter (more lights/space than matches).

P.S. Just watched Bear G. in Man vs. Wild (Discovery channel) use this after a major rainstorm starting a fire on the first strike BECAUSE he had previously harvested and protected some very good tinder. He did not use a magnesium firestarter. It does produce a 5,500°F spark, but it needs a purchase (tinder). Also I want to repeat that the lanyard I got was plenty long, but hey it''s just a piece of cord that you can cut. Live bold. Also the first time I tried to make sparks I made plenty. I do not see how someone could not (unless they had the metal striker upside down read the directions!).

P.P.S. Watched Bear G. in Ecuador (?) NOT be able to start a fire with grass using this because everything was wet and darkness came in not enabling him to search for better (dry) tinder. With typical Bear pluck he stuffed his shirt with the grass for insulation and kept his chin up. I bet the mag would have started a fire.

P.P.P.S. Watched ''Survivorman'' take a mag starter out into the desert and easily start a fire, but he used the edge of his knife to make shavings and strike the flint. I don''t reccomend dulling a knife like this, use the back or anything else. Also he CARVED off magnesium and I have found just SCRAPING works well. Finally on the magnesium starter the flint is a small rod on the side and you don''t whack it like in Jeremiah Johnson, but you just scrape it. I think I read one reviewer that broke his flint and I bet he was whacking it, just like in the movies.

This is a long review because this is a survival tool and you should have confidence in it''s capabilities.

Firesteel IS a great tool for starting fires. it sparks great and starts fires no problem. it took me 3 strikes to start my first fire. didn''t need to scrape the coating off, either.

Firesteel IS NOT a magic wand that you can wave around and command a fire to start on anything. you still need to prepare for a fire, i.e. tinder, kindling, etc. and aim where you are throwing those sparks. It works very easy, but you still need to understand the basic concept of fire starting before you question whether it works or not.

I would definitely depend on this tool in a survival situation!

Buy Light My Fire Original Swedish FireSteel Army 12,000 Strike Fire Starter Now

This product is terrific.

There is a slight learning curve involved with this product that breaks down into two parts:

1) You must know what type of tinder to use for this. If it is not good enough tinder, it will not light.

2) Realize that short, very hard strokes with this is the key. Longer, slightly softer strokes do produce many sparks, but it is the short, repetitive strong ones that create very big and hot sparks which will ignite the tinder into a flame.

Enjoy!

Read Best Reviews of Light My Fire Original Swedish FireSteel Army 12,000 Strike Fire Starter Here

This is a high quality firesteel and works very well. It takes a little practice and some basic firebuilding skills to be able to use it effectively. With a little coaching even my 9 year old son was able to light several fires with various types of tinder. You need to use good tinder and practice your technique to get a good shower of hot sparks right where you need them.

My son recently did a science fair project where where we experimented with several different types of tinder and ignition sources to see which was the best way to build a fire in the wilderness. We tested everything we could get our hands on in both wet and dry conditions. Everything worked OK when dry but after we soaked tinder, matches, lighters, etc. the list got a lot shorter. The lighters and regular matches were all useless. The lighters (butane) eventually dried out and worked again)Waterproof matches still worked but you can only carry so many of these some broke and some didn''t light. The firesteel and Coughlin magnesium block still worked but it took forever to scrape the magnesium block, the shavings kept blowing away, then when we applied the spark the magnesium shavings flashed and were gone almost instantly. We were able to make it work but it was a pain and dulled my knife. Some say to use the back of your knife blade to avoid this.

The best combination(s) when wet was waterproof matches or the fire steel and cotton balls soaked with vaseline and some of the commercial tinders including wet fire pellets and coughlin fire sticks. We scraped the wet fire pellets and fire sticks and scraped the firesteel to send a shower of sparks into the the small particles of tinder. The result was an instant fire that didn''t blow out easily. These things lit even when wet. I can usually get a fire going in 1 5 scrapes. The resulting flame from the tinder was steady in the wind and also lit our kindling (dry sticks, pine needles etc) easily.

We gathered all sorts of tinder at home and in the woods and found lots of things that worked. Cotton balls and dryer lint work great. Any cotton or fuzz from plants works, fine dry leaves as well. I can light shredded paper without too much work. Fine dry grass (shredded / pounded and fuzzed up if necessary) and certain types of tree moss light easily. The finer the tinder the easier it is to light. Cattail fuzz is extremely flammable and lights easily. I had difficulties lighting pine pitch scrapings with sparks but included them in my tinder nest to sustain a fire long enough to get kindling going.

Bottom line is these things work and are a fail safe way to start a fire if you have basic fire building skills. This includes carrying or gathering dry tinder, making a nest for the spark, and having kindling and larger firewood pre-gathered to build and sustain your fire once you get it started. I carry one as an absolutely reliable way to start a fire if I need one. I also carry some waterproof matches, a Bic butane Lighter and some commercial tinder (wet fire or fire sticks). Of all these methods I have the most faith in the firesteel. It was also a lot of fun to learn how to use.

Want Light My Fire Original Swedish FireSteel Army 12,000 Strike Fire Starter Discount?

This "flint" is more expensive than the magnesium bars but it is a little more convinient for making sparks because it has a small handle and an attached striker (you have to find your own tender). I did not have a problem using the attached striker as another reviewer did. I also skipped the step of taking the paint off. I just scraped firmly and the ammount of sparks was crazy. My only complaint is the price but if it lasts as long as claimed it is a bargain compared to matches or lighters.

Save 39% Off

Carpet Express C4 Remanufactured Carpet Steam Cleaner Like Rug Doctor

Carpet Express C4 Remanufactured Carpet Steam Cleaner Like Rug Doctor
  • 100 PSI Demand Pump
  • 85" Lift Vacuum Motor
  • 3.5 Gallon Solution & Waste Tank
  • Factory Remanufactured
  • Free Hand Tool / 11ft Hose

I rented one from Home Depot. I had recently rented the Rug Doctor machine and am not sure which one cleans better. The Carpet Express I am quite sure has better suction. After going over an area 3 times it didn''t feel any wetter than after the first time. Rug Doctor strongly recommends not going over an area more than twice. I did and the carpet got too wet.

CE seems easier to handle that the RD. Pushing it around was less a problem than the RD. It has a rotary brush an opposed to the shaking or vibrating brush on RD. Not sure which brush style cleans better though. Carpet Express seems to remove dirt as well as the Rug Doctor but sucks up more moisture than RD leaving carpets drier. One negative thing, the CE instructions direct you to use the container that collects dirty water to also mix clean water and carpet cleaning detergent. That''s like mopping the bathroom floor with a cleaning solution that''s in the toilet stool. Not a good idea. Just use a clean bucket.

The ideal may be to clean with Rug Doctor and suck up left over moisture with a Carpet Express. Not sure but I am leaning toward the CE as being better than the RD.

I have used pro carpet cleaners and don''t think they do a better job than renting a RD or CE. If you have the time and don''t mind breaking a sweat by all means do it yourself.

(Following reviews from another website)

Carpet Express

Pros:

* Extracted nearly all of the water we put into the carpet swatches.

* Best suited for carpets that are exposed to moderate traffic.

Cons:

* Cleaner may not remove very heavy soils.

* Testers said the cleaner was bulky and heavy to push.

* The handle isn''t height-adjustable; several of our taller testers had to lean forward while using this cleaner. (The one I rented had an adjustable handle like RD)

* The unit cleans and extracts the carpet only on the backward stroke, making it difficult to maneuver around a room.

* Some controls may not be intuitive, and you may have to ask a sales associate for a complete instruction manual.

* Upholstery attachment tools can be used with this cleaner; but they weren''t included with the rental. (I rented from Home Depot and attachment tools came free, RugDoctor at Lowes was an extra $3)

Rug Doctor Mighty Pro

Pros:

* Picked up a significant amount of dirt in Institute tests and should work well on high-traffic areas.

* Extracted almost half of the water we put into the carpets.

* Controls are easy to understand and use.

* Manual is complete and accurate.

Cons:

* The machine cleans and extracts only on the backward stroke, making it more difficult to maneuver around a room.

* Can be heavy to push when filled with water.

* The handle moves forward and backward, but doesn''t extend up or down; several of our taller testers had to lean forward while using this cleaner.

* Solution and water must be mixed in a separate bucket and poured into the tank, which can be messy.

Buy Carpet Express C4 Remanufactured Carpet Steam Cleaner Like Rug Doctor Now

I have rented Rug Doctor to clean my carpeting in the past and tried this Carpet Express unit from Home Depot today. The price was only twenty dollars for four hours. The unit I rented was brand new. It isn''t too heavy and simple to use. It extracted a lot of dirt from my carpet. The problem was that it was unacceptably loud. They should provide a pair of quality ear plugs with this unit! I much prefer the Rug Doctor.

BISSELL Healthy Home Upright Bagless Vacuum Save 13% Off

BISSELL Healthy Home Upright Bagless Vacuum, 16N5F, GreenBISSELL Healthy Home Upright Bagless Vacuum, 16N5F, Green

I''ve wanted to switch to a bagless vacuuming system for awhile, now -simply because constantly having to buy vacuum bags, remembering what size and model number, and "the extra expense" seems to be an unnecessary evil -if ya know what I mean.

For comparison, My current vacuum is an allergy filtration (as I have a couple of constantly shedding pets -Rottweilers and kitty cats), 18.0 12 amp motor, Hoover upright with 5 carpet heights and floor mode with an assortment of tools and is "not" bagless. It gets the job done, but has a few irritating problems. My home gets vacuumed, thoroughly, twice a week.

BISSELL Healthy Home Upright Bagless Vacuum, 16N5F, Green is impressive right out of the box. A larger vacuum than my Hoover, with a nice sturdy feel and in a pretty minty green color.

a few things that really stood out for Me:

Easy to put together, just 4 screws and one is good-to-go, as they say.

Large see through bagless canister -It''s really fun to watch all the stuff getting sucked into the canister... Well, the see-through canister may also come in handy if one ever drops an earring or the Kitty decides to make a toy out of Your Engagement ring while you are soaking in the Jacuzzi -and it ends up in the carpet -never to be found till vacuuming day. One could actually see it, in the canister -as opposed to digging through a funky bag of debris -as with my Hoover).

15" wide sweeper head, with rubberized bumper guards -gets the job done a lot faster! ''nuf said! :)

A large height adjustment dial with 6 carpet heights and a bare floor mode. Dial is easy to read, and turn, for desired selection.

Very long cord -the vacuum also has a quick release cord thingy so one does not have to spend a lot of time unwinding.

2 button, fingertip, operation on handle -"Power On" and "Brush". a "plus" if ya ask me, as I do not want the brush rotating when I''m using the attachments, or vacuuming a floor with a hard surface.

Wide foot pedal, on left, for releasing vacuum from upright position.

Large back wheels -the wheels roll very well on My ceramic and vinyl tiles without scratching or leaving indentations. the BISSELL Healthy Home Upright Bagless Vacuum, 16N5F glided over My carpeted areas -which are a deep plush with thick padding -without dragging.

A wonderful assortment of attachment tools like a TurboBrush Tool (great for cleaning fabric furniture and stairs), Combination Brush, Crevice Tool, and a Telescoping Extension Wand for getting hard to reach places.

BISSELL Healthy Home Upright Bagless Vacuum, 16N5F, is not as eardrum piercingly loud as my Hoover. Actually, the hum of the vacuum is rather pleasant.

Clean-up is a breeze! Just press large button on top of see through dirt canister to release from vacuum, press large button at bottom of canister to open bottom...empty into trash container. tip: pet hair seems to not want to come out easily, but just get out one of those unused chopsticks (most have in kitchen drawer) and gently poke pet hair debris to loosen. When finished, close bottom lid and snap canister back in place. Easy! :)

The three filters are easy to get to for maintenance.

...there are many more features to explore.

Does the BISSELL Healthy Home Upright Bagless Vacuum, 16N5F, sound like what you may be looking for? :) A Pleasure to use! *wonders what to spend all the extra money on that usually went to vacuum bags* Highly Recommended! --Katharena Eiermann, 2012

I''ve (recently) reviewed the BISSELL OptiClean Pet Upright Vacuum, Bronze, 30C7T, an excellent machine, imo, if one has shedding Pets! :)

The brush on this vacuum is powerful. My wife was trying it out when she said that the vacuum felt like it was pulling itself across the carpet. The main suction is also very strong. It did a great job cleaning up the carpet and the hardwood floor. It has a nice handle in the front for carrying and a very long cord.

I had a problem with the brushing attachment on the telescoping pole. It uses suction to spin the brush, and it spins up fine but as soon as it contacts anything it stops rendering it useless. Nothing appear to be cracked or missing in the attachment. I think there may be some air escaping out of the telescoping pole. I didn''t have this issue with the brushing attachment for the the BISSELL 58F83 Rewind SmartClean, Blue model.

Pro: Good Suction on the main vacuum

Pro: has carrying handle

Pro: has hose and attachments

Pro: bag-less

Pro: strong agitating brush

Pro: Large headlight

Pro: Long cord

Con: Weak brushing attachment power

Con: Heavy

Buy BISSELL Healthy Home Upright Bagless Vacuum Now

We liked our old vacuum but we wanted more and what we wanted cost too much. When we saw this vacuum at a reasonable price we figured we''d give it a try. The day it arrived my husband wanted to try it out right away and the next thing I knew, the entire house was vacuumed. Even the wooden floors! This vacuum is so versatile and easy to use.

But wait. How hard are vacuums to use, really? Not much. The truly amazing thing about this vacuum is we have two Siberian huskies and we were using this during "blow out season." If you know nothing about Siberian huskies, trust me when I say that "shedding" is an inadequate description of what they do. If you are familiar with the breed then you know how remarkable it is that even during a blow-out we couldn''t find evidence of fur in our carpet or on the floors.

However, there is one caveat. The Turbo-Brush attachment is great for picking up pet hair, etc., but the place where it''s supposed to click into place for storage on the body of the machine itself is not strong enough to hold it. The minute you turn on the vacuum or roll it around, the vibrations cause the attachment to fall off. I have never actually owned a vacuum that could hold this attachment and when I saw how this one was designed I had a ray of hope because it looked like someone finally got it right. They didn''t.

Other than that, this is a great product and a bargain when compared to the more expensive ones out there making similar HEPA claims. Delighted and highly recommended.

Read Best Reviews of BISSELL Healthy Home Upright Bagless Vacuum Here

We like the idea of the BISSELL Healthy Home Upright, Bagless Vacuum, with a HEPA filtration system that purifies air while vacuuming, purporting to "trap and seal 99.9% of pollen, pet dander" and other allergens. There are allergy sufferers in our home and we live in a canyon where there always seems to be a lot of stuff blowing around.

We have a lightweight canister vacuum but were looking for something that would deal with the nitty-gritty. After several weeks of use, here''s what we''ve found (PROS and CONS) with the BISSELL Healthy Home.

PROS:

It''s powerful--the 9X cyclonic is great for sucking up spiderwebs (and, in some cases, spiders!) and cleaning dust off screens

It''s not too loud.

It''s easy to assemble out of the box.

It does a nice job on carpeting.

CONS:

It''s quite heavy and difficult to maneuver.

The on-board brush is very hard to remove from its vacuum storage port--and to put back in place.

Did we mention that it''s heavy?

All said, we''ll probably use this one for the occasional hard-to-get-at stuff and use our much-lighter canister for the everyday clean-ups. Unless you live in a bungalow, it''s just too hard to carry up and down the stairs.

Want BISSELL Healthy Home Upright Bagless Vacuum Discount?

After using this vacuum for a little while I find that I would recommend it, indeed I have recommended it, though whether this is the best model for you depends on what you need.

My other recent vacuum experience has been the comparably priced Hoover Windtunnel Max Multi-Cyclonic Bagless Upright Vacuum UH70600 and so I''ll be using that as a comparison, since they both have strengths and weaknesses.

First of all, this Bissell is simply more powerful than the hoover. Yes, if you go by how many "cyclones" the Bissell only has 9 of ''em to the Hoover''s 12. But, apparently not all cyclones are made the same as this Bissell really sucks, and I mean that in the best vacuum way possible. It has more suction than the Hoover and for that reason alone the Bissell takes a lead in the comparison.

But suction isn''t everything. And that is where the Hoover jumps ahead. I find myself really liking the auto-retracting cord of the Hoover. I also like the more solid construction. The Hoover just feels like a higher quality vacuum in the feel of the plastic and how well everything fits together.

Both are very easy to use, and the bagless feature is, of course, extremely handy (thanks Dyson for getting that technology moving forward!). The Hoover also has more reach and more/better attachments. The Bissell has the slightly longer cord, which feels more than the 2'' longer of actual distance. I suspect some of the cord in the Hoover gets left in the auto-retract.

So which do I recommend? If you need flexibility and want a more flexible (and smaller in size) vacuum that just looks and feels better, the Hoover is the way to go. If you''re primarily vacuuming floors and need stronger suction, then the Bissell is a fine choice. Indeed the Bissell is what I recommended my brother buy when he was vacuum shopping.

Save 13% Off